8 Ports Web Smart Optic Switches
The STE-208-X3XM is a managed optic fiber switch that offers 8 10/100Base-FX fiber ports.It supports port based VLAN, port bandwidth control, 802.1Q VLAN, 802.1P QOS,etc management features.Chat Now
The STE-208-X3XM is a 10/100mbps fiber plus copper switches that comes with websmart & SNMP
management features.. Offering 8 10/100mbps fiber port, , the STE-208-X3XM optic switch easily extends your network up to 80Km. It could be a good option for your FTTH, FTTO, FTTD solutions.
The STE-208-X3XM supports web & snmp management that enables easy access and manage the switch. Support Telnet, Users can manage the switch remotely. When the network load is too heavy, users can adjust the network flow by IEEE 802.3X packages.
>>> Offering IEEE 802.1P priority, the STE-208-X3XM provides 3 modes of priority.
First-in-first Service: the switch will transmit earlier received data package first.
All-High-Before-Low: the switch will transmit high priority data package first.
Weight-Round-Robin: the switch will transmit data package according to the queue weight, transmit high
priority data package and low priority data alternately. The data package that are for low priority will not be delay or rejected in this way.
>>> Providing Class of Service ( COS ):
With class service configuration and priority control, the STE-208-X3XM implements Qos function.It supports data pakages' high and low priority, three modes of priority mode. If some port's Port Base is chosen, and high priority is enabled, all data package gets into this port will be mapping as high priority.
If VLAN Tag is chosen, the switch will unscramble 3- digit priority mark in Vlan-Tag data package automatically, if that mark is high priority, it will be mapping as high priority.If IP TOS/DS is chosen, the switch will unscramble 8- digit mark in IPV6/IPV4 data package automatically, if this mark is high priority, it will be mapping as high priority.
STE-208-X3XM Websmart & SNMP managed Optic Switch Back View
>>> VLAN Multi to One
This function regards ports as target VLAN, other ports can add into this target VLAN port as a VLAN group. But after this function is active, the original setup of the VLAN group may be replaced or cleared.
>>> Broadcast Storm Control
Broadcast Storm Max Value refers to the Broadcast Storm Limited Value, for example, if Broadcast storm packets received at 100Mbps in 10ms reach 127 (or the pre-set Max Value), switch will detect that Broadcast Storm is happening. And it will start the Broadcast Storm Control function and give up the unnecessary broadcast storm packets.
>>> Port Mirroring:
To monitor more than one port at the same time, supports port monitoring receiving, port monitoring sending and port monitoring of receiving and sending modes, supports monitoring across different VLANs
>>> Port Bandwidth Control:
port bandwidth control enables you to control the transmission rate of each port, including upstream and
downstream, and stop the user of a certain port from using too much bandwidth. And user of other ports will have more stable bandwidth. This function can be used in net café or broadband connection to smart residential area.
Trunk is usually called port aggregation, mainly used for hot backup, fault tolerant in uplink pipeline between switches. Each port can be set to have 2 or 4 ports, port set to trunk group can be used only in trunk group, no matter whether the port is being used in the trunk group or not.
>>> STE-208-X3XM Main Features:
> 8 Port 100Base-FX Half/Full duplex switch ports
> 2048 MAC address table (4-way hashing)
> Two queues for QOS (1:2 or 1:4 or 1:8 or 1:16)
> Port-based, 802.1p and IP TOS priority
> Store & forward architecture and performs forwarding and filtering at non-blocking full wire speed
> An aging function and 802.3x flow control for full duplex and a backpressure function for half duplex
> Packet lengths up to 1522 bytes
> Congestion Flow Control (HOL)
> IEEE 802.1Q Port-based VLAN and adjustable VLAN to support up to 32 VLAN groups
> Broadcast storm filter
> Port Mirroring
> Remote Management by Telnet
> Web management
> SNMP management
> Configure Half/full duplex, auto-negotiation and data-communication via web interface.
> IEEE802.3u 100Base-FX optical Ethernet
> IEEE802.3ah 100Base-BX10
> IEEE802.3x flow control
> IEEE802.1p priority
> IEEE802.1q VLAN
> TCP/IP, DHCP
Optical Interface Options
> Single single-mode fiber, dual wavelengths, SC/PC connector, operating distance 20/40 km
> Dual single-mode fibers, single wavelength, SC/PC connector, operating distance 20/40/60/80 km
> Dual multi-mode fibers, single wavelength, SC/PC connector, operating distance 2 km
IEEE 802.3, IEEE 802.3U, IEEE 802.3X,IEEE 802.1P,IEEE 802.1Q
Number of Ports
8 Port 10/100Base-Fx
Tx: RJ45 FX: SC, ST, FC
Multimode Fiber: 850nm, 1310nm, Singlemode Fiber: 1310nm, 1550nm
10Mbps: 14880pps, 100Mbps:148800pps
Store and Forward
Flow control mode
IEEE 802.3x full-duplex flow control and back pressure flow control
LED status of Link, activity, Full/half duplex, speed, and power on diagnostic function
10Base-T: 3, 4 or Cat 5 shielded / unshielded twisted pair, 100 meters max.,
100Base-TX: Cat 5 shielded / unshielded twisted pair, 100 meters max.
100Base-Fx: 8.3μm, 8.7μm, 9μm and10μm on single mode fiber and 50, 62.5 and 100μm on multi-mode fiber
Single Mode/Multi Mode fiber cable
AC:220V or DC:-48V, 50~60Hz
-20 ℃ to 70 ℃
10% to 90%
-40 ℃ to 75 ℃
5% to 95% RH
>>> OEM Terms & Conditions:
Minimum Order Qty: 20 pcs
Delivery time: 29 days by receipt of payment
Payment Terms: 30-50% Deposit T/T in advance, balance be paid before shipment
Warranty: Two-year, replacements to be shipped together with the shipment of a re-order
Shipping Terms: FOB, CNF, CIF